DS2202A 200 MHz Digital Oscilloscope

RIGOL DS2202A 200 MHz Digital Oscilloscope
Click an image to enlarge
Brand: RIGOL
Warranty: 3 years
Manuals: 
User's Manual (5.7 Mb)
Datasheet (4.56 Mb)

USB Host LAN (Local Area Network)

Retail price: $1,630.00

Depending on a destination shipping cost may vary.
Free shipping for orders over $450
on items weighting under 20 lbs
(certain restrictions apply!)

See shipping page for international rates
or contact sales@tmatlantic.com

In stock, 1 left

Buy Add to cart

Rigol DS2202A digital oscilloscope is an efficient signal research instrument with low noise level, advanced triggering capabilities as well as bus signal synchronization and decode function (I²C, RS-232, SPI etc.).

Original innovative UltraVision technology developed by Rigol combines perfect waveform capture rate, high memory depth, easy captured waveform navigation. In this technology real-time signal record is combined with advanced signal analysis capabilities and bus signal decode function. At the same time the signal is displayed with controllable brightness (up to 256 levels) depending on the signal intensity.

This technology use in Rigol DS2202A makes it a unique oscilloscope for the development and debugging of digital and analogue equipment.

High functionality, user-friendly interface and the low price make Rigol DS2202A digital oscilloscope a perfect instrument for any service center or R&D laboratory.

RIGOL DS2202A Features and Benefits

  • Wider vertical range (500µV/div ~ 10V/div), lower noise floor, better for small signal capturing
  • Full bandwidth, lower overshoot(<5%), perfect frequency response design
  • Bandwidth 200MHz
  • Max. Sample Rate 2G Sa/s
  • Standard Memory Depth up to14Mpts,Optional Memory Depth up to 56Mpts
  • Innovative "UltraVision" technology
  • 50 Ohm Impedance included

Channels2
Bandwidth200 MHz
Sample rate2 GSa/s
Memory depth14 Mpts (standard), 56 Mpts (option)
Vertical resolution (bits)8
Automatic measurement-Duty, +Duty, +Wid, -Wid
InterfaceUSB Host, USB Device, LAN
Display8 inch LCD
Power supply100-240 V
Dimensions361.6 mmЧ 179.6 mmЧ130.8 mm

RIGOL DS2202A digital oscilloscope is another Best-In-Class instrument from Rigol offering an unmatched feature/value package. RIGOL DS2202A is a fast and versatile scope covering frequencies up to 200 MHz with two channels and a wide vertical range (500µV/div-10V/div) to deliver an extremely low noise floor to help you capture smaller signals. Add a 2 GSa/s max. sample rate and 14 Mpts. of standard memory depth to its user-friendly interface and 8 inch WVGA display and you've got a scope that outperforms the competition in a wide range of bench-top and field applications.

Standart accessories

1. Power Cord
2. USB Cable
3. Passive Probes (350 MHz) - 2 pcs
4. A logic analyzer probe
5. Quick Guide
6. Resource CD

Optional accessories

1. Passive Probe (500 MHz)
2. Rack Mount Kit

Frequently Asked Questions

  • High voltage measurement testing are not allowed over 300 volts
  • After the oscilloscope is powered on the display remains dark, what should I do?
  • The measured voltage amplitude value is 10 times greater or smaller than the actual value
  • When changing the horizontal sweep on the digital oscilloscope at different horizontal points observed inexplicable change in the form of the same signal, why is this happening?
  • There is wave form displayed, but it is not stable

  • High voltage measurement testing are not allowed over 300 volts

    Even when you can read in a probe 600V PK CAT I. The Aktakom, Owon or Rigol oscilloscopes does not support more than 300V RMS or 400V PK. For higher voltage please contact us to request a special device.


    Up

    After the oscilloscope is powered on the display remains dark, what should I do?

    Please implement the following fault treatment procedure.

    • Check whether the power cable is connected properly.
    • Ensure the power switch is turned on.
    • Restart the instrument after completing the checks above.
    • If the oscilloscope still can not work normally, please call for service.

    Up

    The measured voltage amplitude value is 10 times greater or smaller than the actual value

    Check whether the channel attenuation coefficient and the attenuation coefficient of the probe used is match.
    Up

    When changing the horizontal sweep on the digital oscilloscope at different horizontal points observed inexplicable change in the form of the same signal, why is this happening?

    In fact, this is not a problem.

    Just keep in mind that you're using a digital oscilloscope, which digitizes the signal with different sampling rates depending on the selected horizontal sweep, and then connects the digitized points with strait line while restoring the real shape of the signal.

    Your first screen shows that you are measuring voltage 50 Hz with the 10 ms / div sweep and a sampling frequency of 20 kHz Ks/s

    One signal period (20 ms), digitized in this mode, 20E-03 (sec) * 20E03 (1/sec) = 400 points. This is enough to properly restore and interpolate a sine wave of 50 Hz (i.e. in a period of 20 ms).

    Normal display, with a sweep 10 ms / div:

    Distortion of the same signal at 10 s / div sweep

    Your second screen is set to sweep 10 sec / div, and sample rate on a sweep turned to 20 samples per second (20 Sa / s). I.e. one signal period 20 ms had: 20E-03 (sec) * 20 (1/sec) = 0.4 points. That means that to restore (to interpolate the points) a sine wave with less than one point in time is impossible, so you get this mess (known as "aliasing" or a false frequency) formed by the beats of the measured frequency and sampling frequency.

    In order to correctly install a data collection in a digital oscilloscope one should follow a simple rule - the sampling rate must be at least 5-10 times higher than the frequency signal, in that case you will not have the issues that we just discussed.

    This applies to all digital oscilloscopes and in no way connected to any particular make or model of oscilloscope or its probes.


    Up

    There is wave form displayed, but it is not stable

    • Check whether the Source item in the TRIG MODE menu is in conformity with the signal channel used in the practical application.
    • Check on the trigger Type item: The common signal chooses the Edge trigger mode for Type and the video signal the Video. Only if a proper trigger mode is applied, the wave form can be displayed steadily.
    • Try to change the trigger coupling into the high frequency suppress and the low frequency suppress to smooth the high frequency or low frequency noise triggered by the interference.

    Up


    Back to the section
    AKTAKOM - the Best in Test Award Winner!
    Site map|Privacy policy|Terms of Use & Store Policies|How to Buy|Shipping|Payment|© T&M Atlantic, Inc., 2010-2024