www.tmatlantic.com
Test & Soldering Equipment On-line Store |
D.E.V.I.C.E. (Wiki)Calculators Services |
Filter by first letter
ABCDEFGHIJKLMNOPQRSTUVWXYZ+-
Reset |
ThesaurusSearch by section D.E.V.I.C.E. servicesThe accuracy of a digital tester is defined as the difference between the reading and the true value for a quantity measured in reference conditions.
In electronics an analog-to-digital converter (ADC) is a system that converts an analog signal into a digital one.
In physics, the angular velocity is defined as the rate of change of angular displacement and is a vector quantity (more precisely, a pseudovector) which specifies the angular speed (rotational speed) of an object and the axis about which the object is rotating.
Since it was founded in 1918, the American National Standards Institute (ANSI) has coordinated the development of voluntary consensus standards in the United States and has represented the needs and views of U.S. stakeholders in standardization forums around the globe. ANSI is the U.S. member body to ISO and, via its U.S. National Committee, the International Electrotechnical Commission (IEC). ANSI is also a member of the International Accreditation Forum (IAF).
Measurement unit that is adopted by convention for a base quantity. For example: The International System of Units (SI) defines seven units of measure as a basic set from which all other SI units are derived.
The Best in Test awards are presented annually by the editors of Test & Measurement World. These awards honor important and innovative new products and services in the electronics test and measurement industry.
The international organization established by the Metre Convention, through which Member States act together on matters related to measurement science and measurement standards...
The set of operations that establish, under specified conditions, the relationship between values of quantities indicated by a measuring instrument or measuring system, or values represented by a material measure or a reference material, and the corresponding values realized by standards.
The set of interrelated or interacting elements necessary to maintain the measurement performance of measuring and test equipment to defined requirements. Measurement unit for a derived quantity.
Examples: the metre per second (m/s) and the centimeter per second (cm/s) are derived units of speed in the SI. The kilometre per hour (km/h) is a unit of speed outside the SI but accepted for use with the SI. The knot, equal to one nautical mile per hour, is a unit of speed outside the SI.
Conversion of discrete sequence of digital data, which represents a signal amplitude at certain points of time, to continuous analog signal.
Dynamic measurement is the measurement of a physical quantity which is changing in size.
EUROLAB was created in Brussels on April 27, 1990 on the basis of a memorandum of understanding, signed by delegations representing the private and public laboratories of 16 out of the 19 countries of the EEC and EFTA.
Any noise whose power spectral density varies inversely with frequency.
In physics, a force is any influence that causes an object to undergo a certain change, either concerning its movement, direction, or geometrical construction. It is measured with the SI unit of newtons and represented by the symbol F.
Noise whose probability distribution or probability density function is gaussian. Noise that is steady or stationary in character and originates from the sum of a large number of small events, tends to be gaussian by the central limit theorem of probability theory.
The offset of a measurement decision value from a stated specification or tolerance.
IEEE is the world’s largest technical professional organization dedicated to advancing technology for the benefit of humanity.
The IAF is the world association of Conformity Assessment Accreditation Bodies and other bodies interested in conformity assessment in the fields of management systems, products, services, personnel and other similar programmes of conformity assessment.
World’s leading organization for the preparation and publication of International Standards for all electrical, electronic and related technologies. These are known collectively as “electrotechnology”.
ILAC is the international organisation for accreditation bodies operating in accordance with ISO/IEC 17011 and involved in the accreditation of conformity assessment bodies including calibration laboratories (using ISO/IEC 17025), testing laboratories (using ISO/IEC 17025), medical testing laboratories (using ISO 15189) and inspection bodies (using ISO/IEC 17020).
ISO is an independent, non-governmental international organization with a membership of 167 national standards bodies.
Through its members, it brings together experts to share knowledge and develop voluntary, consensus-based, market relevant International Standards that support innovation and provide solutions to global challenges.
The International System of Quantities (ISQ) consists of the quantities used in physics and in modern science in general, starting with basic quantities...
Internet of Things (IoT) is the network of physical objects.
Rate at which a body moves in a straight line from one location to another.
Measuring instrument reproducing or supplying, in a permanent manner during the use, quantities of one or more given kinds, each with an assigned value (weight piece, volume measure, standard electric resistor, line scale, gauge block, standard signal generator).
The result of a process to provide adequate confidence that a measurement will satisfy stated requirements.
The probability that an incorrect decision will result from a measurement.
The set of operations to determine the value of a measurement quantity.
An attribute of a phenomenon, artifact, or substance that may be distinguished qualitatively and determined quantitatively.
The probability that all the applicable measurement quantities of measuring and test equipment are within tolerance.
It is a scalar quantity, defined and adopted by convention, with which any
other quantity of the same kind can be compared to express the ratio of the
two quantities as a number.
The measuring instrument, measurement standard, reference material or auxiliary apparatus, or a combination thereof, necessary to realize a measurement process.
Device used for making measurements, alone or in conjunction with supplementary device(s).
A measuring instrument alone may be considered to be a measuring system.
A measuring instrument may be an indicating measuring instrument or a material measure.
Device used in measurement which provides an output quantity having a specified relation to the input quantity (thermocouple, current transformer, strain gauge, pH electrode, Bourden tube, bimetal strip).
The component of the output noise power that arises from sources within the network under test. This component of output noise is usually differentiated from the component that comes from amplifying the noise that originates in the input source for the network.
The temperature (Ta) that yields the available power spectral density from a source. It is obtained when the corresponding reflection coefficients for the generator and load are complex conjugates.
A group of people and facilities with an arrangement of responsibilities, authorities, and relationships.
In digital imaging a pixel (px) is the smallest addressable element in a raster image or the smallest addressable element in a dot matrix display device.
The name given to a region in an electric circuit in which charged particles would tend to move from one place to another.
The amount of energy produced or consumed per unit time.
As a rule PPM (“part per million”, where 1 PPM = 0,0001%) is used to show devices precision in the frequency domain or other devices of high precision.
Radiation coefficient is a term used for the conditions description of the materials when they radiate energy.
Why exceptionally flush? When the end of a lead or wire must be soldered it is often necessary to have it as flush as possible to insure a highly reliable solder joint. If a wire is to be coated or if it needs to be threaded into some hole it may be necessary to have no burrs or “pinch” on the wire end. Delicate components are less likely to suffer shock when cut by an exceptionally flush cutter.
Static measurement is the measurement of a physical quantity considered invariable during the whole measurement period according to the specific measurement target.
Test & Measurement World is a community of engineers who are working at the cutting edge as well as in the trenches of electronic test. Its goal is to support engineers, developers, and industry-related management in their test needs.
The ratio of the span of the tolerance of a measurement quantity subject to calibration, to twice the 95% expanded uncertainty of the measurement process used for calibration.
Articles 1 - 50 of 62 First | Prev. | 1 2 | Next | Last |
|
Site mapPrivacy policyTerms of Use & Store PoliciesHow to BuyShippingPayment |