AKTAKOM APS-3320LS Benchtop DC Power Supply Programmable Remote Controlled (USB or LAN) is designed for industrial, laboratory and other engineering solutions. There is a four-wire (4-wire) connection scheme used. Includes Aktakom Power Manager Software for Windows (including Windows 10). Available software development kit (SDK) for LabVIEW, C++, LabWindows-CVI and MS VB is designed to help users in developing their own applications for AKTAKOM power supplies.
Depending on a destination shipping cost may vary. See shipping page for international rates or contact firstname.lastname@example.orgSold out
AKTAKOM APS-3320LS Single Output DC Regulated Bench remote controlled programmable power supply with Adjustable Current limit. Large Digital Display with LED meter displays Volts & Amps. Push button switch allows connection & removal of load. Multiturn Voltage control for precise settings. Front panel output Banana Jacks & Terminal strip for remote Voltmeter Sensing at the load.
There is a four-wire (4-wire) connection scheme used. This connection method provides accurate voltage supply preset in the load. This leads to the compensation of the wire resistance connecting the power supply and the load that is especially important in the industrial application of the power supply.
There is a single channel, output regulated voltage of 0…30 V, output current of 0…20 A.
AKTAKOM APS-3320LS DC power supply differs from other similar power supplies by wide capabilities of local and remote control through AKTAKOM Power Manager software.
APS-3320LS remote controlled DC power supply is capable of operating in several modes:
Manual control mode. Including the use of 4 memory cells to store preset voltage and current.
Remote control mode to operate AKTAKOM APS-3320LS DC power supply by computer via USB interface through AKTAKOM Power Manager Software. Moreover the USB interface has full galvanic isolation between the power supply and the computer.
Remote control mode to operate AKTAKOM APS-3320LS DC power supply by computer using an USB cable or LAN cable (ethernet).
Remote control mode to operate AKTAKOM APS-3320LS DC power supply throught the remote access to the computer USB-connected to APS-3320LS. AKTAKOM Power Manager Software provides the operation in «server-client» mode even for power supplies without built-in LAN interface. Meanwhile the power supply is physically connected to computer-server via USB interface and the data is available for reading from any computer of the network.
AKTAKOM Power Manager Software (APM) provides a wide range of control capabilities of output voltage and stabilization current both in manual and functional modes. Functional control is a very powerful tool of APM software which allows you not only to control your AKTAKOM power supply automatically by computer but also to program its off-line operation mode by prespecified algorithm. Functional control mode in APM software allows automatically controlling the output parameters (voltage and current) of the power supply according to the principle specified with the help of graphics and tabular editors. In a convenient graphics editor user may specify 10 standard forms of parameters (including sine, square, triangle, saw, flash, pulse, 2 types of exponents, 2 types of S-curves), as well as, almost any arbitrary form which can be described formulary. The program operation in equipment operation compatibility mode is also available.
The software system for AKTAKOM APS-3320LS remote controlled DC power supply includes a software development kit (SDK) This SDK contains the device driver with all necessary functions for the power supply operation and represents dynamic-link library (DLL) Windows followed with the library header file in the C programming language, with LabWindows function tree and the tool library for LabVIEW which fully repeats it. Additionally (in contrast to APS-3xxxLx_SDK_Base Software Development Kit) it contains the examples of programming in the following development environment: Borland C++ Builder, MS Visual C++, NI LabWindows/CVI and NI LabVIEW.
Input: 110/220VAC 50Hz/60Hz
Output: 0-30VDC @ 0-20A
Attractive digital display shows voltage and current
High precision voltage regulation
Proqressive current regulation
Dual terminal system: Safety test style or expandable screw terminals
Four-wire (4-wire) connection scheme used. This connection method provides accurate voltage supply preset in the load. This leads to the compensation of the wire resistance connecting the power supply and the load that is especially important in the industrial application of the power supply
Button to connect/disconnect the load
Digital display shows voltage and current with LEDs
How to connect to the power supply via web-interface?
There is no web-interface remote control feature for this power supply. To control the power supply remotely use the software provided in the standard accessory kit for the device. Up
Do AKTAKOM power supplies have short circuit protection?
Yes they have.
Almost all modern power supplies have two operation modes: voltage stabilization mode and current stabilization mode. In case of short circuit the power supply automatically switches from the output voltage stabilization mode to the output current stabilization mode, and the output voltage starts proportionally dropping. At the same time the current in the load connected to the power supply will be limited with the value set with the screwdriver slot used to adjust the output current value on the front panel of the power supply. For the best protection it is recommended to set a low current value. In case of short circuit the current in the connected load will be limited with the value set on the power supply. Up
May I use AKTAKOM power supplies to charge accumulators?
AKTAKOM power supplies can’t be used for accumulator charging since it may cause the accumulator breakage (recharge, electrolyte boiling, extra pressure of the internal gas which will lead to the accumulator explosion). Accumulators should be charged with the current source which controls the accumulator voltage and regulates the charging current accordingly. When the required accumulator voltage is achieved such type of source simply stops the charging process, its name is a charging device.
How to see a device serial number in AKTAKOM Power Manager software?
The program automatically reads the serial numbers of all devices found. To detect the device open Settings window, go to Connection and Presets tab, select the right device type you need in the list of models and click “Detect”:
In the list of detected devices you will see all names and serial numbers of the devices found.
After you select one of the detected devices and connect it to the program its serial number will be displayed in the program main window title. Up
AKTAKOM File Converter (AULFConverter)
AKTAKOM File Converter (AULFConverter) is an utility to convert AKTAKOM data file format used in AKTAKOM applications including APM to other formats such as CSV and WAV.
AKTAKOM Net Configurator is designed to record and read the network settings data of AKTAKOM Universal Lab devices (supporting AULNet protocol). The application provides simple and convenient user interface to work with settings, they can be recorded into the file and read afterwards.
AUNLibUSB device driver for Windows supports AKTAKOM USB Lab instruments (PC-based oscilloscopes and other). AUNLibUSB driver is a low-level program which does not communicate with user directly neither has user interface. After its installation in the operating system the driver starts working as a part of this operating system and supplies applications with the access to the resource of AKTAKOM supported devices and appropriate programs.
This full version kit is designed to help users in creating their own applications for the following devices: APS-31xxL, APS-33xxL, APS-36xxL. Capable of working in Windows and LabView environments with USB and LAN interfaces.
Fuente de Poder CD regulable con limite de corriente ajustable de una salida. Pantalla grande digital con indicador LED para mostrar voltios y amperios. Boton interruptor de salida y eliminación de carga. Control de multivuelta para el ajuste preciso del voltaje. Conectores en el panel frontal tipo "Banana" y regleta de salida para voltimetro de teledetección de la carga.
Entrada: 110 VAC 60 Hz
Salida: 0-30VDC @ 0-20A
Pantalla digital atractiva muestra de voltaje y corriente
Ventilador de enfriamiento
Alta precisión de regulación del voltaje
Regulación Proqresiva de la Corriente
Dos Sistemas de terminales: Banana con seguridad y de tornillos expandibles