Since soldering and rework processes when repairing electronics are usually made sequentially by one specialist it’s obviously convenient to use a universal system combining the features necessary for both operation types.
AKTAKOM ASE-4202 professional multifunction station unites in one block a soldering station and SMD rework equipment with digital temperature indication. This allows ASE-4202 to occupy a minimal space and organize a high performance work area.
AKTAKOM ASE-4202 soldering and rework station is ESD-safe. This is an important requirement that should be met since the absence of antistatic protection may cause the damage of valuable electronic components with electro static discharge.
ASE-4202 rework station has a hot air gun and a soldering iron accordingly. It is especially recommended for work with temperature sensitive electronic components such as QFP, PLCC, SOP, BGA, etc.
AKTAKOM ASE-4202 is equipped with high-quality heating element that can be easily replaced. This heating element is covered with alumoceramic layer and inserted into ceramic housing. Such a reliable structure fully isolates the heating element from the environment effect and therefore protects the heating element from corrosion providing its high durability accordingly. Such heating element provides very fast heating up.
Multilayer (copper, steel and stannum) cover of the soldering iron tip operating part has excellent thermal conduction and provides optimal high effective heat transmission.
AKTAKOM ASE-4202 soldering and rework station has a power saving feature. That means that in 10 minutes of no use the station will automatically decrease the temperature to some steady level that will efficiently protect the nozzle and the heating element.
- Multifunctional integrated desoldering maintenance system combined by rework station and soldering station
- The core of the whole machine is controlled by the single and microwave chip to assure the temperature accuracy and stability of rework station and soldering station
- Clear digital display of the current working temperature and conditions
- Temperature of rework station and soldering station is adjusted by digital buttons
- The two stations can work separately
- Temperature block system
- Fault indication function
When the new machine is operated for the first time, you must install the handle frame, the picture is as follows: According to your habits, you can screw the four screws tightly. Under your need, remove the two screws of the fixed handle shelf on the right or on the left. Put the two installation holes of the handle in the fixed screw holes, and screw the two removed screwed tightly. Put the components of the handle on the frame and check if suitable.
Open the master power switch at the back panel of the device after connected the power. In the case of two heat switch closed, LED display show the rework station in waiting state with "--1"
Put on the heat switch, LED display show the current open sets. Three seconds later, display the actual work state. At same time, the heat channel shows indicator lights.
Put off the heat switch of current working channel, it will stop heating. If LED previously displays working state of one channel, now it shows the other channel working state or waiting state.
After using it, remember to cool the machine. You should put the handle on the shelf. When the machine is in the waiting state, you can make the power off, which will extend the service life of soldering station &SMD rework. If you don't use it, you should put the heat switch and master power switch at the back panel off.
Digital display conversion
On the condition of connected power, push the “SET” cord to transform between the two channels, and the connected channel show indicator lights.
After connected power, if the display shows the state you need, you can directly press the "up” or “down” cord to converse the temperature of this channel. If not, you should press “SET” cord, then press “UP” or “DOWN” cord to converse temperature. Accomplish the display settings, three seconds later, display shows the actual work state.
The waiting state of hot air rework
If you do not use this device temporary and please put the handle on the handle frame, the device will cut down hot air. When the temperature is less than 100°?, the rework station becomes in waiting state. Now the state of LED display showing is the situation of soldering station &SMD rework. If the device come into operating state, the display will automatically converse to the state of soldering station & SMD rework, otherwise, it will show "SLP", the waiting state. Under the waiting state, display does not show state neither of the two channel. LED display shows the working state of soldering station & SMD rework and restores last time settings, as long as you hold the handle of the rework station again.
Display "--1" means the rework station partly does not start that the heating cord is off.
Display “SLP” means the rework station enters the waiting mode.
Display "--2" means the soldering station partly does not start that the heating cord is off.
Display “S-E” means there is something wrong with the sensor of the working channel, so the device stops outputting signal.
Display “H-E” means the heating elements of the channel may be damaged partly.
Bottom of the decimal point of the display: all are lighting which means heating; all snub out which means stopping heating; some is flicker means the temperature of one channel, at least, is stably.
You should correct temperature after changing the heating elements or iron tip. When you correct temperature, please use no sense and suitable screwdriver stretch into corresponding hole of “CAL”, then rotate fine tuning toward left or right.