Depending on a destination shipping cost may vary. Free shipping for orders over $450 on items weighting under 20 lbs (certain restrictions apply!) See shipping page for international rates or contact sales@tmatlantic.com
AKTAKOM ASE-1128 Temperature controlled soldering station is suitable for soldering SMDs (surface mounted devices) that require diverse power levels. The control dial is used to set the required power level. The soldering tip reaches a temperature of approx. 450°C.
AKTAKOM ASE-1128 soldering station (analog of ZD-928) is used for soldering of micro components that require low power. Due to specific use of this station and its low cost ASE-1128 is sold as no refunds or exchanges, all sales are final.
Specifications
Channel: 1 assembling channel
Analog control
Max. station power: 8W
Temperature range: 100°C - 450°C
Max. power of the soldering iron: 8W
Soldering iron voltage supply: 12V
Mica heating element
Included accessories
Soldering Station
Soldering iron
Soldering iron holder
User manual
Operation instruction for AKTAKOM ASE-1128 soldering station
Operate AKTAKOM ASE-1128 soldering station on a clean, horizontal, safe, stable and heat resistant surface.
Check whether the on/off switch on the back of the device is off.
The soldering iron together with the soldering tip and the connection cable form one unit. Connect the cable round plug to the socket on the front panel of the soldering iron station.
Remove the plastic cover from the soldering tip and insert the soldering tip into the spiral holder on the soldering iron station.
Connect the power plug to an appropriate power outlet.
Turn on the soldering iron station, the power indicator on the front of the device will light up red.
Turn the control knob clockwise to the desired power level.
Start soldering as soon as the device has heated up sufficiently. Do not operate the device continuously at the highest power level. After 15 minutes maximally of continuous operation at the highest power level, turn the control knob to the medium power level to prevent the soldering tip from overstraining.
During breaks or after the end of work, put down the soldering iron in the spiral holder on the soldering iron station with the soldering tip facing downward. Turn the control knob to the low power level during breaks.
Turn off the device with on/off switch.
Unplug the device and allow it to cool down sufficiently at a safe location.
When the temperature stabilizes, clean the tip with the cleaning sponge and check the condition of the tip.
If there is black oxide on the solder-plated portion of the tip, apply new solder (containing flux) and wipe the tip on the cleaning sponge. Repeat until the oxide is completely removed. Coat with new solder. The solder protects the tip from oxidation and prolongs the life of the tip.
If the tip is deformed or heavily eroded, replace it with a new one.
Tip’s temperature High soldering temperatures can degrade the tip. Use the lowest possible soldering temperature. The excellent thermal recovery characteristics ensure efficient and effective soldering event at low temperatures. This also protects the sensitive components from thermal damage. Cleaning Clean the tip regularly with a cleaning sponge, as oxides and carbides from the solder and flux can form impurities on the tip. These impurities can result in defective joints or reduce the tip's heat conductivity. When using the soldering iron continuously, be sure to loosen the tip and remove all oxides least once a week. This helps prevent reduction of the tip temperature. When not in use Never leave the soldering iron sitting at high temperature for long periods of time, as the tip's solder plating will be covered with oxide, which can greatly reduce the tip's heat conductivity. After use Wipe the tip and coat it with fresh solder. This helps to prevent tip oxidation.
Where can I find out more information on the operation of a ASE-1128 soldering station?
If you have more questions, contact our technical support service or other technical personnel. Up
What is the maximum soldering iron tip temperature?
The soldering tip reaches a temperature of approx 450 °C.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. Up
ASE-1128 Unboxing Soldering Station for Micro Components
La estación de soldadura de temperatura controlada ASE-1128 es adecuada para soldar SMD (dispositivos de montaje en superficie) que requieren diversos niveles de potencia. El botón de control se utiliza para establecer el nivel de potencia requerido. La punta del soldador alcanza una temperatura de aprox. 450 ° C.
Esta estación de soldadura se utiliza para la soldadura de micro componentes que requieren baja potencia. Debido al uso específico de esta estación y su bajo costo, ASE-1128 se vende sin reembolsos o cambios, todas las ventas son definitivas.