Depending on a destination shipping cost may vary. Free shipping for orders over $450 on items weighting under 20 lbs (certain restrictions apply!) See shipping page for international rates or contact sales@tmatlantic.comIn stock
The DT830B is a digital multimeter that can measure AC and DC voltage, DC current, resistance. It has diode and transistor test functions as well.
For your convenience the device has a large display. Compact size and light weight will allow you to take it with you simply putting in into your pocket.
Wide operating temperature: 32°F to 104°F / 0°C to 40°
Storage temperature: 10°F to 122°F / -12°C to 50°C.
Relative humidity: 75%
3,5digit LCD, 7 segment, 0.5" high
Dimensions: 5x2.8x1 in / 126x70x25mm
Weight: 6 oz / 170g
AC voltage
Frequency range: 45Hz to 450Hz.
Range / Resolution / Accuracy:
200V; 100mV; ±1.2 % ± 10
750V; 1V; ±1.2 % ± 10
DC voltage
Range / Resolution / Accuracy
200mV; 0.1mV; ±0.5 % ± 2
2000mV; 1mV; ±0.5 % ± 2
20V; 10mV; ±0.5 % ± 2
200V; 100mV; ±0.5 % ± 2
1000V; 1V; ±0.8 % ± 2
Input impedance: 1MΩ.
Maximum input voltage: 1000V DC or 750V rms (200mV scale: 500V DC or 350V AC rms)
DC current
Range / Resolution / Accuracy
200µA; 0.1µA; ±1.0% ± 2
2000µA; 1µA; ±1.0% ± 2
20mA; 0.01mA; ±1.0% ± 2
200mA; 0.1mA; ±1.5% ± 2
10A; 10mA; ±3.0% ± 2
Overload protection: F250mA 250V fuse (10A range is unfused!).
Resistance
Range / Resolution / Accuracy
200Ω; 0.1Ω; ±0.8% ± 3
2000Ω; 1Ω; ±0.8% ± 2
20kΩ; 10Ω; ±0.8% ± 2
200kΩ; 100Ω; ±0.8% ± 2
2000kΩ; 1kΩ; ±1.0% ± 2
Maximum open circuit voltage: 3.2V.
Overload protection: 250V rms. AC on all ranges.
Diode testing
Voltage approx.: 2.8V
Current: 1mA.
Overload protection in the diode test mode: 250V RMS AC.
Over range: LCD will indicated "1"
AC voltage measurement
Connect the red lead to "VΩmA" and the black one – to "COM"
Set the rotary switch to the required V~ range
Connect the test leads across the source or load that you would like to measure. Check the voltage value on the LCD.
DC voltage measurement
Connect the red test lead to "VΩmA” and the black one – to "COM”.
Set the rotary switch to the required range. If you do not know the voltage which should be measured set the range switch at the highest range position and then reduce it until the required resolution.
Connect the test leads across the source or load that you would like to measure. Check the voltage value and polarity on the LCD.
DC current measurement
Connect the red test lead to "VΩmA” and the black one – to "COM”. To measure current between 200mA and 10A, insert the red lead into "10A” (unfused) jack.
Set the rotary switch to the required range.
Open the circuit in which the current should be measured and connect the test leads in series with the circuit.
Check the voltage value on the LCD as well as the polarity of red lead connection.
Resistance measurement
Connect the red test lead to "VΩmA” and the black one – to "COM”. In this mode the red lead polarity is positive “+”.
Set the rotary switch to the required range.
Connect the test leads across the resistance that should be measured and see the results on the LCD.
Note: If the resistor under measurement is connected to a circuit, turn the power off and discharge all capacitors before applying measurements!
Transistor test
Before transistors insertion into the socket for testing make sure to disconnect the test leads from any measurement circuits. No components should be connected to the hFE socket when making voltage measurement with the test leads!
Set the rotary switch to "hFE”.
Determine the transistor type under testing, NPN or PNP, and locate the emitter, base and collector leads.
Insert the leads into the proper sockets of hFE.
Diode test
Connect the red test lead to "VΩmA” and the black one – to "COM”. The red lead polarity is positive "+”.
Set the rotary switch to diode position.
Connect the red lead to the diode anode under testing and the black lead – to the diode cathode.
Check the results in mV on the LCD. If the connection is reversed there will be "1” figure displayed.
El DT830B es un multímetro digital que puede medir voltaje de CA y CC, corriente CC, resistencia. Tiene funciones de prueba de diodo y transistor también.
Para su comodidad, el dispositivo tiene una gran pantalla. El tamaño compacto y el peso ligero le permitirán llevarlo con usted, simplemente guardándolo en su bolsillo.