90M-T-3C Soldering Tip

AKTAKOM 90M-T-3C Soldering Tip
Click an image to enlarge

Retail price :$7.00

Depending on a destination shipping cost may vary.
Free shipping for orders over $450
on items weighting under 20 lbs
(certain restrictions apply!)

See shipping page for international rates
or contact sales@tmatlantic.com

In stock

BuyAdd to cart

Soldering iron tip for AKTAKOM ASE-1101, 1102, 3101, ASE-1105, ASE-1106, ASE-4203, ASE-4204 soldering stations with bevel sharpening at the angle of 45 degrees. Such tips are used for the soldering of QFP microchip.

Soldering tips are made of oxygen-free copper with the steel center and nickel-chromic external covering, the correct use secures a long service life. The long exploitation term of the tips is gained due to their multilayer structure in which the external layer (chrome) is protective, internal (copper) is responsible for heat conductivity, intermediate (steel) for durability and long operating life. And a working part (tin) for good solder wettability.


  1. Multilayered Soldering tips dont need any sharpening.
  2. Unreasonable high temperature shortens service life. Use the minimal acceptable temperature, if possible.
  3. Soft tip cleaning from carbon is made with a damp cellulose sponge as oxide and carbides of solder and gumboils can pollute a tip affecting the soldering quality and decreasing the heat transfer.

    See how to use a sponge for soldering iron.
  4. During continuous work, its necessary to take the tip off and to complete cleaning from oxides no less than once a week. Solder on the tip must stay even in a cold condition.
  5. Do not use aggressive soldering flux, consisting of chlorides, or acid. Use colophony flux.
Tips for soldering stations ASE-1101, 1102, 3101 with bevel sharpening at the angle of 45 degrees
For assembling microchip with lead pitch to 0.02-0.03in/0.5-0.8mm tip 90M-T-3C is used

Such tips are used for the soldering of QFP micro-chip

Punta de soldador para estaciones de soldadura AKTAKOM ASE-1101, 1102, 3101, ASE-1105, ASE-1106, ASE-4203, ASE-4204 con afilado de bisel en un ngulo de 45 grados. Estos consejos se utilizan para soldar el microchip QFP.

Las puntas de soldadura estn hechas de cobre sin oxgeno con el centro de acero y la cubierta externa de nquel-cromo, el uso correcto asegura una larga vida til. El largo plazo de explotacin de las puntas se gana debido a su estructura multicapa en la que la capa externa (cromo) es protectora, la interna (cobre) es responsable de la conductividad trmica, intermedia (acero), por su durabilidad y larga vida til. Y una parte de trabajo (estao): para una buena humectabilidad de la soldadura.

1.Las puntas de soldadura multicapa no necesitan afilarse.
2.La temperatura alta irrazonable acorta la vida til. Use la temperatura mnima aceptable, si es posible.
3.La limpieza suave de la punta del carbn se realiza con una esponja de celulosa hmeda, ya que el xido y los carburos de soldadura y gumboils pueden contaminar una punta que afecta la calidad de la soldadura y disminuye la transferencia de calor.

Vea cmo usar una esponja para soldar.
4. Durante el trabajo continuo, es necesario quitar la punta y completar la limpieza de los xidos no menos de una vez por semana. La soldadura en la punta debe permanecer incluso en condiciones de fro.
5. No utilice fundente de soldadura agresivo, que consiste en cloruros o cido. Use flujo de colofonia.

Back to the section

Please give us your feedback to help us improve our website

* - required fields

Site map|Privacy policy|Terms of Use & Store Policies|How to Buy|Shipping|Payment|© T&M Atlantic, Inc.,2010-2020