Depending on a destination shipping cost may vary. Free shipping for orders over $450 on items weighting under 20 lbs (certain restrictions apply!) See shipping page for international rates or contact sales@tmatlantic.comSold out
Subscribe
Description
Specifications
Accessories
Application
FAQ
Descripción
AKTAKOM ACM-2047 is a compact clamp meter with AC/DC resolution of up to 1 mA/ 10 mA.
"Absolute measurement error" service allows you to estimate the measurement accuracy considering uncertainty (error) in the absolute value. It's important if you take measurements at the range edge when the error value contributes to the value displayed on the device screen.
To get the value range it'd be enough to enter the estimate of the value under measurement into Value input field and to see the range of possible values taking all of the standardized errors into consideration.
Note: a point is used as a separator of the integer and fractional part.
DC Current
Range
Resolution
Accuracy
Absolute error
Value-error
Value
Value+error
40 A
10 mA
±(1%+2 digits)
±0.4199 A
A
150 A
100 mA
±(1%+2 digits)
±1.699 A
A
200 A
100 mA
±(2.2%+2 digits)
±4.5978 A
A
400 A
100 mA
±(4%+2 digits)
±16.196 A
A
AC Current
Range
Resolution
Accuracy
Absolute error
Value-error
Value
Value+error
500 mA
1 mA
±(2%+7 digits)
±16.98 mA
mA
4 A
1 mA
±(2%+4 digits)
±0.08398 A
A
40 A
10 mA
±(1.5%+4 digits)
±0.63985 A
A
100 A
100 mA
±(1.5%+4 digits)
±1.8985 A
A
200 A
100 mA
±(2.5%+4 digits)
±5.3975 A
A
400 A
100 mA
±(5%+4 digits)
±20.395 A
A
Specifications:
Grip diameter: 0.9 in / 23 mm
Single button pressing to set “0” when measuring the direct current
Noncontact frequency measurement
AC True RMS measurement
3¾ digit LCD (4032 digits)
40-segment analog scale
Measurement rate: 3 measurements per second
Simultaneous hold of max. and min. values
Data hold function
Overload indication: OL
Battery: 2 pcs, 1.5V, AA-type
Dimensions: 7.2 x 2.4 x 1.4 in / 183 x 61.3 x 35.6 mm
How can I take relative measurement with Aktakom ACM-2047 clamp meter?
ZERO button can be also used to take relative measurements of DC and AC strength. After you press ZERO the current value turns to 0. All next measurements are shifted by the measurement value which was prior to 0 setting. To return to the normal mode keep ZERO button pressed for 2 s. This measurement mode can be canceled with MAX/MIN buttons. Up
How can I measure maximum and minimum values with Aktakom ACM-2047 clamp meter?
To enter the mode of maximum and minimum values use MAX/MIN button. Every single pressing will display the maximum and then the minimum value for the time of measurement in this mode. To return to the normal mode keep MAX/MIN button pressed for 2 s. Up
How can I measure direct current with Aktakom ACM-2047 clamp meter?
1. Before you start measuring DC strength press ZERO button to set ACM-2047 values to 0.
Since the device has rather high sensitivity, in order to escape noise caused by the external magnetic field, user should set 0 in the same terms which will be used while taking measurements.
2. Open the clamp meter jaws and grab a single wire with current. Close the jaws.
Note: Air gap between the jaws is not acceptable.
It’s not acceptable either to grab several wires with current since it will cause incorrect measurement results.
3. See the readings on the device display.
Up
How can I measure frequency with Aktakom ACM-2047 clamp meter?
1. Make sure the wire under measurement contains alternating current not less than 0.1A.
2. Set the rotary switch to Hz, open the clamp meter jaws and grab the wire under measurement. Open the clamp meter jaws and grab a single wire with current. Close the jaws.
Note: Air gap between the jaws is not acceptable.
It’s not acceptable either to grab several wires with current since it will cause incorrect measurement results.
4. See the readings on the device display.
Up
AKTAKOM ACM-2047 es un medidor de pinza compacto con resolución de CA / CC de hasta 1 mA / 10 mA.