Reliable DC power supply, can be widely used in factory production line. High Regulation. Low ripple and noise. 2 LED displays (voltage / current). Overload / reverse polarity / short circuit / overheat protection. 1 Channel; 30V, 3A
Depending on a destination shipping cost may vary. Free shipping for orders over $450 on items weighting under 20 lbs (certain restrictions apply!) See shipping page for international rates or contact sales@tmatlantic.com
Sold out
Subscribe
Description
Specifications
Accessories
Application
FAQ
Descripción
AKTAKOM APS-1303 is a highly reliable constant voltage DC power supply. This kind of power supply can be widely used in factory production line, in the electronic circuit such as operational amplifier, digital logic circuit etc.
APS-1303 has 2 LED displays for current and voltage values accordingly:
voltage display accuracy: LED 1%2 byte
current display accuracy: LED 1%2 byte
Output terminal of AKTAKOM APS-1303 are 0.2 in / 4 mm banana jacks.
Features
Light and compact design, the power supply occupies very little working area.
Dimensions: 9.8 x 5.9 x 6.3 in / 260 x 150 x 160 mm
Power Cord
User Manual
Operation instructions
Ensure that the power plug of this unit is connected to a 110V AC power outlet before using, switch the power ON, and adjust the (8)~(9) knobs to set the voltage to the desired value, and then plug your output cords into the output terminals (10)~(11), now the current meter (1) will show the current value.
The limiting value of the output current is 3A or 5A depending upon the model, you must disconnect the power immediately when the over load indicator (6) is on.
Setting of current limiting.
- Use a short-circuit wire to short the current terminals (+) to (-).
- Adjust the current knob untill the CC indicator is on.
- Adjust the current knob to the desired value (4) & (5).
- Take off the short circuit wire.
(1) Current meter: displays output current value
(2) Voltage meter: displays output voltage value
(3) Power switch: control the power
(4) Output current fine knob
(5) Output current course knob
(6) Constant current mode indicator
(7) Constant voltage mode indicator
(8) Output voltage coarse knob
(9) Output voltage fine knob
(10) Power output “-” terminal
(11) Output “+” terminal
(12) Ground (Earth terminal)
May I use AKTAKOM power supplies to charge accumulators?
AKTAKOM power supplies can’t be used for accumulator charging since it may cause the accumulator breakage (recharge, electrolyte boiling, extra pressure of the internal gas which will lead to the accumulator explosion). Accumulators should be charged with the current source which controls the accumulator voltage and regulates the charging current accordingly. When the required accumulator voltage is achieved such type of source simply stops the charging process, its name is a charging device.
La fuente de poder AKTAKOM APS-1303 es una fuente de corriente continua de alta fiabilidad y de voltaje constante. Tiene características tales como limite por voltaje bajo y protección de cortocircuito. Puede ser ampliamente utilizado en las líneas de producción de las fábricas.
La fuente de poder de corriente directa es de un canal. Voltaje nominal de 0 a 30V (ajustable). Corriente nominal 0~3 A (ajustable). Potencia nominal 90 W. Precisión Tensión/Corriente ± 0.5% lectura + 2 dígitos. Pantalla de dos Leds con una resolución de 0,1 V (voltaje) / 0,01 A (actual). Vibración y ruido: ≤ 3 mVrms. Carga de Estabilidad (<3 A): ≤ 0,1% 5 mV. Dimensiones: 260x150x160 mm / 9.8"x5.9"x6.3"
Características
Diseño ligero y compacto
0.01% Regulación de alta
Pantalla con 2 Leds indicadores
Regimen de operación constante de voltaje y corriente
Baja vibración y ruido
Protección de sobrecarga y polaridad invertida
Limite de corriente por bajo voltaje y protección de cortocircuito
Ventilador de potencia alta y protección por temperatura alta
Ideal para Laboratorios educativos. Muy seguro para su uso